 |
GWM Weld Screw |
|
Thread Size |
M3.5-6g | M4-6g | M5-6g | M6-6g | M8-6g | M10-6g | |
|
Thread Pitch |
0.6 | 0.7 | 0.8 | 1 | 1.25 | 1.5 | |
|
Head |
A-Diameter | 7.0 ± 0.25 |
8.0 ± 0.25 |
1+ 0.0 ± 0.25 |
12.0 ± 0.30 |
16.0 ± 0.30 |
2+ 0.0 ± 0.40 |
| H-Height | 1.1 ± 0.13 |
1.2 ± 0.13 |
1.6 ± 0.13 |
1.9 ± 0.13 |
2.5 ± 0.13 |
3.1 ± 0.13 |
|
|
Projections |
P-Diameter | 1.40 ± 0.13 |
1.78 ± 0.13 |
2.13 ± 0.13 |
2.54 ± 0.13 |
3.10 ± 0.13 |
3.56 ± 0.13 |
| F-Height | 0.53 ± 0.05 |
0.64 ± 0.05 |
0.81 ± 0.05 |
1.02 ± 0.05 |
1.20 ± 0.05 |
1.40 ± 0.05 |
|
|
Thread Size |
M3.5 x 0.6-6g | M4 x 0.7-6g | M5 x 0.8-6g | M6 x 1-6g | M8 x 1.25-6g | M10 x 1.5-6g | |
| Length (Overall) L | 6.0 | GWM 03506 | GWM 04006 | ||||
| 8.0 | GWM 03508 | GWM 04008 | |||||
| Tolerance | 10.0 | GWM 03510 | GWM 04010 | GWM 05010 | GWM 06010 | ||
| Up to 25mm | 12.0 | GWM 03512 | GWM 04012 | GWM 05012 | GWM 06012 | ||
| + 0.0 | 14.0 | GWM 03514 | GWM 04014 | GWM 05014 | GWM 06014 | ||
| - 0.8 | 16.0 | GWM 03516 | GWM 04016 | GWM 05016 | GWM 06016 | GWM 08016 | |
| Over 25mm | 20.0 | GWM 03520 | GWM 04020 | GWM 05020 | GWM 06020 | GWM 08020 | GWM 10020 |
| to 50mm | 25.0 | GWM 03525 | GWM 04025 | GWM 05025 | GWM 06025 | GWM 08025 | GWM 10025 |
| + 0.0 | 30.0 | GWM 04030 | GWM 05030 | GWM 06030 | GWM 08030 | ||
| - 1.6 | 35.0 | GWM 05035 | GWM 06035 | GWM 08035 | GWM 10035 | ||
| Over 50mm | 40.0 | GWM 05040 | GWM 06040 | ||||
| + 0.0 | 45.0 | GWM 05045 | GWM 08045 | GWM 10045 | |||
| - 2.3 | 55.0 | GWM 10055 | |||||
 |
An OHIO metric GWM weld screw has three projections on top of the head for welding to the sheet surface, not through it. From a design standpoint, the GWM screw will eliminate the necessity for holes, thus is ideal for those applications where product appearance or potential leakage is a prime consideration. There are no screw heads to protrude or spoil appearance or the product. With GWM metric screws, the exterior surface is left virtually unmarred. The GWM weld screw is an excellent choice for blind locations too, because it can be permanently pre-attached. |
 |
|
Material: |
C1010 High-Welding |
Tensile Strength: |
60,000 psi | |
| Quality, Low Carbon Steel |
Yield Point: |
30,000 psi | ||
|
Finish: |
Plain, Unless Specified |
Shear Strength: |
30,000 psi | |
|
Threads: |
ANSI / ASME B 1.1-1989 |
Elongation 2” |
30% Max. |